• DECEMBER CLUB HOLIDAY PARTY!!!
    Hi Guest: The RS holiday party will be on Friday, December 11 at 7:00 p.m. The holiday party will be held indoors at the fabulous Golden Gate Canyon Grange. Click here for details and directions. Please note that there will not be a meeting on the first Wednesday of December -- the holiday party will serve as our official meeting instead.

Brake booster and MC upgrades for tons on an 85-89 4Runner

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
Looking to move to tons (60/14b or 609s) on my '88 4Runner, and need some brake help. I know I can upgrade to the dual diaphragm booster from a '93 T100, and then either go with the matching T100 master cylinder, or adapt a GM one. The question I have is what are the dimensions of these parts, compared to the original booster and MC I have? Since linking the front, I only have 1/4" forward of the MC 'till I hit the intake, and 1/4" below the existing MC 'till I hit the shock tower. If anyone has either setup and can measure, I'd sure appreciate it.

Brake booster and MC upgrades for tons on an 85-89 4Runner - post #1 by ScaldedDog


20261114_131158.jpg


This setup extends 12 3/8" from the firewall, and the booster is roughly 9" in diameter.

Thanks!

Mark
 
Last edited:

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
I ended up ordering both the Toyota and GM master cylinders, as well as a T100 booster, from Amazon, so I should be able to figure out the measurements by mid-week. I saw where the booster "diaphragm" diameter is 9.75". If that's the outer diameter of the casing, and if it is no deeper, I'll be OK. If that actual diaphragm is 9.75", making the case something like 10.5", then there's no way it'll fit.

That begs another question: Might any of you have upgraded from the smaller (13/16" or 7/8") MC to either the T100 one, or a GM one, but kept the old booster? I'm loath the swap the booster if I don't have to, since anything I get today would be cheap junk, and I may not be able to get the old one out, anyway. The shock tower from my link setup is pretty close.

Mark
 
Last edited:

FJCDan

Rising Sun Member
Joined
Aug 9, 2010
Messages
1,097
Location
West Denver
Mark, do you already have a 14 Bolt? If not I have one sitting in my back yard looking for a home. Would love to get this gone.
 

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
Mark, do you already have a 14 Bolt? If not I have one sitting in my back yard looking for a home. Would love to get this gone.
Hey Dan. I don't, but my current plan is to get a shaved housing center section and associated parts from a guy on Marketplace, then custom cut new tubes for it. We'll see how that works out. What can you tell me about yours:

WMS?
Year (88 and earlier or 89 and newer)?
Pics if convenient, but don't spend a lot of time.

I'm not committed to the HP60/14b combination, as I'm considering custom 609s, too. It's all eye-wateringly expensive, so my index finger involuntarily curls up when I hold it over the "submit order" button for either option.

Mark
 

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
...as well as a T100 booster, from Amazon, so I should be able to figure out the measurements by mid-week. I saw where the booster "diaphragm" diameter is 9.75". If that's the outer diameter of the casing, and if it is no deeper, I'll be OK. If that actual diaphragm is 9.75", making the case something like 10.5", then there's no way it'll fit.
Yeah, I know. I'm quoting myself. A guy on Irate informed me that I already have a dual diaphragm booster, as evidenced by the step-down in diameter visible in the photo above. I didn't think those showed up in 4Runners 'till '90, but that is apparently not correct.

Mark
 

jps8460

Cruise Moab Committee
Cruise Moab Committee
Joined
Feb 15, 2013
Messages
3,285
Location
Grand Junction

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
Saw this thread and was going to chime in yesterday while waiting for a car in a pit and totally spaced it.

Check out the Bosch Ibooster https://www.bosch-mobility.com/en/solutions/braking-systems/ibooster/

That doesn’t solve your MC size problem but might help with the booster side of things. Several folks make adapters.

Man, that is slick! It's more technology than that contained in my entire fleet, though. :ROFLMAO: Since I have the dual diaphragm booster, already, I should be good there. The trick now will be to find an MC that'll fit in my limited space. I should know in a day, or two.

Mark
 

FJCDan

Rising Sun Member
Joined
Aug 9, 2010
Messages
1,097
Location
West Denver
Hey Mark, It is axle off a 93 Chevy van I bought from Steve H in the Springs years ago when I needed an engine. I think it had maybe 88K on it. Drum brakes, full float axles. I will send you some pic's today.
 

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
The GM MC showed up today, and won't come close to working. It's enormous, and makes the Toyota ones look like... toys. With the 1" adapter it would require to bolt to the booster, it would go clear through my intake tube.

The 1 1/16" one from a one ton T100 will fit, though, so I'll likely keep it. Strangely, it's shorter than the stock one.

Mark
 

Gerty

Wincher
Joined
Oct 5, 2022
Messages
88
Hello fellas! Mark, good cell phone call we had today but memorializing some of what we chatted about (and more) here in this thread.

1) Master clyinder: I bought my truck with an upgraded (what I believe is a) Land Cruiser 80 master with a 1" bore, so i have zero insight into what your stock master cylinder's stopping abilities/bore are compared to my "upgraded" MC. I believe that my truck is running a stock booster. Moreover, you and I have not only different generation vehicles, but also different engines so there's no way I can opine on what iterative upgrades will mean between mine and yours, especially since I don't even 100% know my own truck in the absence of an upgraded MC (meaning I can't opine on the stock MC's abilities). However, what I will tell you is that my truck (with Wilwood 2-piston brakes on all 4 corners, and Trail Gear rotors, and 40" sticky tires, and 4,000 lbs vehicle weight) stops on a dime - locks up all tires tires on pavement type thing. The Wilwood MC that I have that I told you about when we spoke is part number 260-8555. The Wilwood proportioning valve I have is part number 260-13190. The former is really large in size but it's an awesome unit. In addition to the above, I have two completely separate Wilwood proportioning valves that are more universal if you're so intersted (I don't have the part number, but smaller than the 260-13190 part number).

2) Third members: For any vehicle, I understand that low pinion (LP) rear is stronger than high pinion (HP) rear given drivng on the drive side of the ring and not the coast side of the ring in an LP setup. The opposite is the case with the front. I'm running HP front and rear Gearworks thirds and have ZERO concerns with the strength of my HP rear. Why? because of vehicle weight and low power engine (although having dual tcases undermines what I just said). Like I told you, I would rather sacrifice strength for some ground clearance in a crawler application. The opposite would be the case if I had a baja truck or dragster. I'm running Gearworks 10" thirds which (which to my knowledge just means a 9" case but a 10" ring) but there's no issue with avoiding crazy expense and instead running a 9" HP front and a 9" HP/LP rear. I'm getting a little bit out of my wheelhouse with regards to 9"/10" case compatability or dimensions but I think I'm right that there's no such thing as a 10" case and the case dimensions for my 10" third and a 9" third are identical (the only thing that's not is the ring gear; could be wrong). But for cost sake, there's nothing wrong whatsoever in running a 9" HP front and 9" LP rear. Nor is there anything wrong with running a 60 HP front and a 14b LP rear.

3) Random tidbits: My wheel-mount to wheel-mount surface (WMS) width is 69.25" (if I can remember right). And with my particular wheel offset and backspacing, my outside tire-outside tire dimension is like 85". I would NOT go any wider than my WMS. In fact, if I were to do it again for my application, I'd do 67" or 68" WMS. A lot of folks like as wide as 72" WMS but unless you're doing WE Rock or Ultra4, I don't think it's warranted. Obviously the wider the more stable, but there have been more than a few times during Colorado or South Dakota wheeling where trees materially interfere with where I can and can't go, simply because of my axle width. Second tidbit - I used a 4Wheel Underground kit for the front (not the rear, because I had the rear backhalved) and while it's a phenomenal kit (the best you can buy), I've learned that with a simple bit of math, generic link brackets and maybe even shock towers will work just as well. Third tidbit: the everlasting 6 lug vs 8 lug debate - to avoid what I believe to be unnecessary expense, stick with your 6 lug wheels. 8 lug setup is obviously stronger but again if you're not racing, not running 42s, don't have v8 power, and have a relatively "light" vehicle (like you do), don't upgrade to 8 lug if you have 6 lug wheels. I run 6 lug with 40" stickies and knock on wood, have had zero issues, zero "bad feelings", zero noises, and zero regret. Preference would be to run 8 lug but I was already running 6 lug and didn't see a compelling reason to justify the expense of a new set of wheels just so I could run 8 lug. Final tidbit: I recently removed my locking unit hubs (let me know if you're intersted in the Yukon hubs) and replaced them with drive flanges in the front. This warrants a broader conversation but for me, it eliminates yet another failure point. BUT, that decision will be how much it's driven vs trailered, what type of front locker you have, how driveable you want it, full hydro vs hydro assist (related to driveability), etc.

Let me know what else you're wondering about be it here or by cell!
 

ScaldedDog

Hard Core 4+
Joined
Dec 18, 2005
Messages
1,336
Location
Sedalia, CO/NSB, FL
Thanks Derek! Great to talk to you today, and I look forward to getting together!

I figured out in the last few days that I may have a 15/16" MC. 13/16" would be WAY more common, but the appropriate number on the side looks like a 5 to me. Either way, no way I can lock up 40s on pavement, even with the dual diaphragm booster (which is also a rarity). It's been fine for wheeling, but better wouldn't hurt. I have a 1 1/16" MC from a one ton T100 that I'm planning to use.

Thanks so much for the rest of your post! I really appreciate the time you put into it, and your experience. If I pull the trigger on this project - and I need to either do so or holster my weapon - I'll start a thread and pull in your post. Great stuff!!

Mark
 
Back
Top