Danger Noodle
Trail Ready
As some of you may know, I just recently finished my 40, and I already am feeling like it is time for some changes, mainly in the suspension. I'm wanting to link the rear, but my driveline is too long to get any effective link system in there, so I am looking to change. My loss is your gain, I guess. I'm posting this as a feeler to see if anyone is interested in a drop-in driveline that is tested and known. You could even drive it before you decide you want it.
Anyways, specs. Everything has been 100% professionally rebuilt, I have all receipts in hand. The engine has been dyno tested, and I have complete specs on it. I currently have ~1200 miles on everything. You are getting a basically new drivetrain.
What you get:
Engine: SBC 383 Stroker.
-Sealed Power Pistons ( Don't remember how much it was bored over)
-Clevite Main Bearings
-Durabond cam bearings
-NEW Melling HD oil pump
-Comp Cam and lifters (I'll add a photo of cam card)
-Scat Cast Stroker Crank
-ARP Intake and Head Studs
-New Cast Aftermarket Vortec (062 spec) heads.
-NGK Plugs
- Proform Valve Covers
-Dual Plane Intake
-Holley Sniper 4150 EFI
-Holley Hyperspark Ignition and Distributor
-New High Output Alternator, Starter, A/C Compressor, Water Pump, Power Steering Pump.
-180 Degree Thermostat.
This engine is dyno tested at 400 HP & 450 TQ at 7,000 feet in elevation. It was built for torque, and the torque curve is really great from idle.
Transmission: 1999 GM K2500 NV4500 (5.61 first, synchronized)
-New 3rd gear
-New 5th gear
-Complete rebuild, all bearings, synchros, etc.
-Have ONLY run AMSOIL 75W-90 Synthetic gear oil in this case.
-OEM Shifter
Doubler : Marlin Toybox (# 009 or 600) 2.2:1
-Rebuilt by Georg @ Valley Hybrids.
-Marlin Shifter
Transfer Case: 34MM Idler Split Case (2.3: 1)
-Rebuilt by Georg @ Valley Hybrids.
-Georg Twinstick Shifters
Centerforce clutch, with new OEM FJ40 Slave Cylinder
Holley In-Tank 255 LPH regulated fuel pump, with a massive chunk of Holley Hydramat.
Frostbite 3 core radiator
AA Jeep Conversion Long-Tube headers
New Severe duty fan and fan clutch (installed ~500 miles ago)
I have over 18K (With receipts) invested into this setup. I'm willing to negotiate, so if you are interested, let's talk! As an added bonus, you get an amazing crawl ratio out of this; I'm currently at 156:1.
Anyways, specs. Everything has been 100% professionally rebuilt, I have all receipts in hand. The engine has been dyno tested, and I have complete specs on it. I currently have ~1200 miles on everything. You are getting a basically new drivetrain.
What you get:
Engine: SBC 383 Stroker.
-Sealed Power Pistons ( Don't remember how much it was bored over)
-Clevite Main Bearings
-Durabond cam bearings
-NEW Melling HD oil pump
-Comp Cam and lifters (I'll add a photo of cam card)
-Scat Cast Stroker Crank
-ARP Intake and Head Studs
-New Cast Aftermarket Vortec (062 spec) heads.
-NGK Plugs
- Proform Valve Covers
-Dual Plane Intake
-Holley Sniper 4150 EFI
-Holley Hyperspark Ignition and Distributor
-New High Output Alternator, Starter, A/C Compressor, Water Pump, Power Steering Pump.
-180 Degree Thermostat.
This engine is dyno tested at 400 HP & 450 TQ at 7,000 feet in elevation. It was built for torque, and the torque curve is really great from idle.
Transmission: 1999 GM K2500 NV4500 (5.61 first, synchronized)
-New 3rd gear
-New 5th gear
-Complete rebuild, all bearings, synchros, etc.
-Have ONLY run AMSOIL 75W-90 Synthetic gear oil in this case.
-OEM Shifter
Doubler : Marlin Toybox (# 009 or 600) 2.2:1
-Rebuilt by Georg @ Valley Hybrids.
-Marlin Shifter
Transfer Case: 34MM Idler Split Case (2.3: 1)
-Rebuilt by Georg @ Valley Hybrids.
-Georg Twinstick Shifters
Centerforce clutch, with new OEM FJ40 Slave Cylinder
Holley In-Tank 255 LPH regulated fuel pump, with a massive chunk of Holley Hydramat.
Frostbite 3 core radiator
AA Jeep Conversion Long-Tube headers
New Severe duty fan and fan clutch (installed ~500 miles ago)
I have over 18K (With receipts) invested into this setup. I'm willing to negotiate, so if you are interested, let's talk! As an added bonus, you get an amazing crawl ratio out of this; I'm currently at 156:1.
Last edited: